Silencer Remote PN: SLRF41 FCC ID: H50T21

Extended warranty is available on the checkout page.

This remote has an FCC ID of H50T21. It is commonly mispelled as H5OT21. This remote transmits at 434MHz and has a remote start and a keyless entry button. This XT-33 remote was made for the Autopage RF-215, RF-220, RF-315, RF-420, RS725LCD, RS727LCD, RS-660, RS-662, and RS-622. XT-33 can be used to replace XT-42LCD, XT-59, XT-60, XT-61, XT-62, XT-65S, and XT-72S. Those remotes worked on: RS-622, RF-420LCD, RF-305, RF-310, RF-405, RF-410, RS-650Plus, RS-610Plus, RF-1050KE, RF-1055KE, RF-105KE, RS-727LCD, RS-662. Our remotes are tested on keyless entry signal testers before we ship it to you. Free tech support is available to help you program the vehicle to accept the remote.

Autopage has gone out of business but Silencer makes this remote which can work as a replacement for the autopage remotes above. As a Silencer remote, it can be used on the SL-2, SL-3, SL-42, SL-5, SL-52, SL-6, and SL-62 systems.

Programming Instructions:

First begin by identifying what you are using it to replace

• If your old remote was an SLRF41 and the system in your car is SL-2, SL-3, SL-42, SL-5, SL-52, or SL-62, use the instructions below.

1. Turn the Ignition ??witch ??FF/ON??3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and hold in on the 3rd push, when a long chirp is heard then release the valet switch.  You are now in the Transmitter programming mode.
3. Press any button on transmitter 1 until the siren responds with a confirming chirp; the first transmitter is
now programmed.
4. Press any button on the second transmitter until the siren responds with a confirming chirp; the second
transmitter is now programmed.
5. Apply the same procedure to program 3rd and 4th .Transmitters.
6.  Turn Ignition to ??FF??position, or leave it for 15 seconds. 3 long chirps and 3 parking light flashes will confirm exit.
Note: If more than 4 transmitters programmed, the system will only keep the last four.

• If your old remote was an Autopage XT-33, XT-65S, or XT-72S, use the instructions below.

1. Turn the Ignition ??witch ??FF/ON??3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 2 times and hold in on the 2nd push, when a long chirp is heard then release the valet switch.  You are now in the Transmitter programming mode.
3. Press any button on transmitter 1 until the siren responds with a confirming chirp; the first transmitter is
now programmed.
4. Press any button on the second transmitter until the siren responds with a confirming chirp; the second
transmitter is now programmed.
5. Apply the same procedure to program 3rd and 4th .Transmitters.
6.  Turn Ignition to ??FF??position, or leave it for 15 seconds. 3 long chirps and 3 parking light flashes will confirm exit.
Note: If more than 4 transmitters programmed, the system will only keep the last four.

• If your old remote was an Autopage XT-59, XT-61 or XT-62, use the instructions below.

1. Turn the Ignition switch to the ON position.
2. Push the Valet switch 3 times.  There will be 1 long chirp and 1 short chirp.  You are now in the Transmitter programming mode.
3. Press any button on transmitter 1 until the siren responds with a confirming chirp; the first transmitter is
now programmed.
4. Press any button on the second transmitter until the siren responds with a confirming chirp; the second
transmitter is now programmed.
5. Apply the same procedure to program 3rd and 4th .Transmitters.
6.  Turn Ignition to ??FF??position, or leave it for 15 seconds. 3 long chirps and 3 parking light flashes will confirm exit.
Note: If more than 4 transmitters programmed, the system will only keep the last four.

• If your old remote was an Autopage XT-60, use the instructions below.

1. Turn the Ignition ??witch ??FF/ON??3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times.  There will be 1 long chirp.  You are now in the Transmitter programming mode.
3. Press any button on transmitter 1 until the siren responds with a confirming chirp; the first transmitter is
now programmed.
4. Press any button on the second transmitter until the siren responds with a confirming chirp; the second
transmitter is now programmed.
5. Apply the same procedure to program 3rd and 4th .Transmitters.
6.  Turn Ignition to ??FF??position, or leave it for 15 seconds. 3 long chirps and 3 parking light flashes will confirm exit.
Note: If more than 4 transmitters programmed, the system will only keep the last four.