Important Note:

Please note that aftermarket remote controls are not universally compatible. They are designed for specific aftermarket systems.

If you're here without checking your existing remote's FCC ID/Part Number or your system model under the dash, please contact us at:

+1-386-586-3650

Omega 422-07 Keyless Entry alarm Remote Transmitter L2MAL41T

SKU: Z4050A

Condition: Refurbished
Precio:
Precio de venta$24.95

Gastos de envío calculados en la caja

Stock:
Disponible

Descripción

This remote has an FCC ID of L2MAL41T.  It has a red LED light that lights up when you press the buttons.  This remote features two buttons.  This remote sends it's codes across 310 MHz.  The remote is tested on a Keyless Entry Tester before shipping to ensure it is sending the correct codes, proper signal strength, and has a good battery.  Free technical support is available via phone and email to help you perform programming if you have difficulty.

PROGRAMMING INSTRUCTIONS for C-2, C-2+, C-2+P, Freedom 150, Freedom 200, Freedom 200+, Freedom 200+P, K9-FIVE T, M.A.T.-5T:
Before you begin, your system must be in a disarmed state and you must know where your valet switch is located. Perform the following steps:
1) Turn the vehicle's ignition to the "on" position
2) Within 7 seconds of step 1, press the valet switch 5 times. The alarm should respond with a long siren chirp.
3) Press the large/ lock button on your remote. The alarm should respond with a short siren chirp.
4) Repeat step 3 for each additional remote that is to operate the system (up to 4 remotes).
Note: the system will automatically exit programming mode if it detects a 15 second period of no activity.

PROGRAMMING INSTRUCTIONS for Model #1:
Before you begin, your system must be in a disarmed state and you must know where your valet switch is located. Perform the following steps:
1) Turn the vehicle's ignition to the "on" position
2) Within 7 seconds of step 1, press the valet switch 5 times. The alarm should respond with a long siren chirp.
3) Press the valet switch to enter your secret override code. If a code has never been programmed, press the valet switch one time. The alarm should respond with a long siren chirp.
4) Press the large/ lock button on your remote. The alarm should respond with a short siren chirp.
5) Repeat step 4 for each additional remote that is to operate the system (up to 4 remotes).
Note: the system will automatically exit programming mode if it detects a 15 second period of no activity.

PROGRAMMING INSTRUCTIONS for C-514:
Before you begin, your system must be in a disarmed state. Perform the following steps:
1) Turn the vehicle's ignition from "off" to "on" 5 times within 7 seconds. The system should respond with a horn honk or the door locks will lock then unlock.
2) Press the large/ lock button on your remote. The system should respond with a short horn honk or the door locks will lock then unlock.
3) Repeat step 2 for each additional remote that is to operate the system (up to 4 remotes).
Note: the system will automatically exit programming mode if it detects a 15 second period of no activity.

PROGRAMMING INSTRUCTIONS for K9-ONE C:
This type of alarm automatically enters transmitter programming mode upon power up. Before you begin, make sure that all points of entry (doors, trunk, hood) are closed. If there is a hood pin switch, have a friend hold it down or temporarily disconnect it. The system will not enter programming mode if it detects an open point of entry.
Perform the following steps:
If the system has been without power for more than 24 hours:
1) Apply power to the system.
2) Press the large/ lock button (Press small center button for Freedom 400) on your remote. The system should respond with a short siren chirp.
3) Repeat step 2 for each additional remote that is to operate the system.
If the system has had power within the last 24 hours:
1) Disconnect and re-apply power.
2) Press the large button (Press small center button for Freedom 400) on any remote that does not already operate the system (this is how the system determines that you want to program transmitters). The system should respond with a short siren chirp.
3) Repeat step 2 for each additional remote that is to operate the system.
Note: the system will automatically exit programming mode if it detects a 15 second period of no activity.

Gastos estimados de envío

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)